void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
Serial.println("Hello World");
}
void loop() {
// put your main code here, to run repeatedly:
Serial.println("Hello World");
delay(1000);
}
업로드
그리고
저거 누르면
실행이 된다
이제 LED 를 만들어보자
브레드 보드를 꺼네준다
10번이 긴거임니다!!! 긴거가 10
잘 써주고
int ledPin = 10; //LED가 연결된 아두이노의 디지털 10번(D10)은 "ledpin"으로 정의
void setup() {
// put your setup code here, to run once:
pinMode(ledPin, OUTPUT); // ledpin(D10)은 출력
}
void loop() {
// put your main code here, to run repeatedly:
digitalWrite(ledPin,HIGH); //ledpin(D10)에 HIGH의 디지털 출력
delay(1000);
digitalWrite(ledPin,LOW); //ledpin(D10)에 LOW의 디지털 츨력
delay(1000);
}
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone? vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening
# on the IPv6 "any" address (::) will accept connections from both IPv6
# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific
# addresses) then you must run two copies of vsftpd with two configuration
# files.
listen_ipv6=YES
#
# Allow anonymous FTP? (Disabled by default).
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
#write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time
# in your local time zone. The default is to display GMT. The
# times returned by the MDTM FTP command are also affected by this
# option.
use_localtime=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
#xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories. See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
# (Warning! chroot'ing can be very dangerous. If using chroot, make sure that
# the user does not have write access to the top level directory within the
# chroot)
#chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# Customization
#
# Some of vsftpd's settings don't fit the filesystem layout by
# default.
#
# This option should be the name of a directory which is empty. Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem
rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key
ssl_enable=NO
#
# Uncomment this to indicate that vsftpd use a utf8 filesystem.
#utf8_filesystem=YES
## 이건 수정본
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone? vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening
# on the IPv6 "any" address (::) will accept connections from both IPv6
# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific
# addresses) then you must run two copies of vsftpd with two configuration
# files.
listen_ipv6=YES
#
# Allow anonymous FTP? (Disabled by default).
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
#write_enable=YES
#
write_enable=YES
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#local_umask=022
#
local_umask=022
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time
# in your local time zone. The default is to display GMT. The
# times returned by the MDTM FTP command are also affected by this
# option.
use_localtime=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories. See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
# (Warning! chroot'ing can be very dangerous. If using chroot, make sure that
# the user does not have write access to the top level directory within the
# chroot)
#chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# Customization
#
# Some of vsftpd's settings don't fit the filesystem layout by
# default.
#
# This option should be the name of a directory which is empty. Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem
rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key
ssl_enable=NO
#
# Uncomment this to indicate that vsftpd use a utf8 filesystem.
#utf8_filesystem=YES
##이건참고용
# anonymous 사용자의 접속 허용 여부, 즉 anonymous ftp (default = YES)
# 공개된 형태의 FTP 서버로 운영할 것이 아니라면 NO로 한다.
anonymous_enable=NO
# 로컬 계정 사용자의 접속 허용 여부 (default = NO)
local_enable=YES
# write 명령어 허용 여부 (defualt = NO)
write_enable=YES
# 로컬 계정 사용자용 umask (default = 077)
local_umask=022
# anonymous 사용자가 파일을 업로드 할 수 있는지 여부 (default = NO)
# anon_upload_enable=YES
# anonymous 사용자의 디렉토리 생성 허용 여부 (default = NO)
# anon_mkdir_write_enable=YES
# 파일 전송 로그를 남길 것인지 여부 (default = YES)
xferlog_enable=YES
# xferlog 표준 포맷으로 로그를 남길지 여부 (기본 설정파일은 YES)
# 아래에서 NO로 설정했을 때를 설명함
xferlog_std_format=YES
# 파일 전송 로그 파일명
xferlog_file=/var/log/vsftpd.log
# FTP 서버 접속할 때 로긴 메시지 (default = vsFTPd 버전번호)
# 한글 사용 가능
# ftpd_banner=Welcome to blah FTP service.
# 사용자의 홈디렉토리를 벗어나지 못하도록 제한하기 위한 설정 (default=NO)
# 제한이 필요할 경우 YES로 바꾼 후 제한할 사용자 ID를 chroot_list_file= 에 설정한 파일에
# 지정한다.
# chroot_local_user= 설정과 관련이 있으니 '3. 문제 해결'을 꼭 읽어보라.
#
# chroot_list_enable=YES
# chroot_list_file=/etc/vsftpd.chroot_list
# -------------------------------------------------------------------
# 기본 설정 파일에는 없는 설정값으로 필요한 설정만 추가한다.
# ※ 중요한 설정은 굵은 글씨로 표시
# -------------------------------------------------------------------
# PAM 파일명을 지정 (설치할 때 /etc/pam.d/vsftpd명으로 복사함)
pam_service_name=vsftpd
# wtmp에 로그 남기기 (YES로 해야만 last 명령어로 접속 여부 확인 가능)
session_support=YES
# 사용자가 자신의 home directory를 벗어나지 못하도록 설정
chroot_local_user=YES
# 새로운 디렉토리에 들어갔을 때 뿌려줄 환경 메시지를 저장한 파일명
# message_file=.message
# xferlog 형식으로 log를 남기려면 (위에서 이미 YES로 했음)
# xferlog_std_format=NO
#
# - xferlog 표준 포맷은 로긴, 디렉토리 생성등의 로그를 남기지 않음
# 그러나 vsftpd 스타일 로그는 이를 포함한 보다 상세한 로그를 남김
# - vsftpd 스타일 로그 예
#
# Sun Jul 12 01:38:32 2003 [pid 31200] CONNECT: Client "127.0.0.1"
# Sun Jul 12 01:38:34 2003 [pid 31199] [truefeel] FAIL LOGIN: Client "127.0.0.1"
# Sun Jul 12 01:38:38 2003 [pid 31199] [truefeel] OK LOGIN: Client "127.0.0.1"
# Sun Jul 12 01:38:41 2003 [pid 31201] [truefeel] OK MKDIR: Client "127.0.0.1", "/mp3"
# Sun Jul 12 01:39:06 2003 [pid 31201] [truefeel] OK UPLOAD: Client "127.0.0.1", "/델리
# 스파이스 5집 - [04]키치죠지의 검은 고양이.mp3", 6855473 bytes, 3857.39Kbyte/sec
# 전송속도 제한 (0은 제한없음, 단위는 초당 bytes)
anon_max_rate=0
local_max_rate=0
trans_chunk_size=0
# 최대 접속 설정 (단 xinetd를 통하지 않고 standalone으로 동작할 때만 사용 가능)
# standalone을 위해서는 listen=YES 추가하고 별도로 vsftpd를 띄워야 함
#
# max_clients=최대 접속자 수, max_per_ip=IP당 접속 수
# max_clients=100
# max_per_ip=3
# Standalone 으로 운영할 때 listen=YES. 포트 변경을 원할 경우 listen_port 설정
# 디폴트 포트는 21번 포트이다.
# listen=YES
# listen_port=21
